Muhammad Mukarram Technical Services L.L.C

Category Blog

Air Conditioning Blows Hot Or Warm on One Side – Free Car AC Help

Car air conditioning systems that blow warm on one side and cold on the other side usually have one of two problems. In this short auto repair article, a master automotive technician shares his experience, derived from working on air conditioners in Florida for the last couple of decades. This free information can be equally helpful to the do-it-yourselfer as it is to a consumer that knows the value of being informed when it comes to dealing with car repair shops. Read on for free car A/C help when the air is blowing warm on ONE side.

Usually cars that blow cold on one side of the dash and warm on the other side, are typically equipped with a dual zone climate control system. Dual zone systems allow the driver and front passenger to adjust respective temperatures to their comfort levels. There are two common causes of a temperature difference when both sides are set at the coldest settings, lets cover the first one.

Low Refrigerant

Automotive air conditioners which use 134A, usually hold a small amount of refrigerant compared to older automobiles that use R12. Car and truck air conditioners today are much more efficient than their older counter parts. The fact that 134A systems use less freon, means that a leak can more quickly affect the performance of an HVAC (Heating Ventilation & Air Conditioning) system. Due to the design of dual AC systems, low refrigerant is the leading cause of drastic temperature difference from one side of the dash to the other. Even well experienced car mechanics may be surprised to learn that as little as 4 to 8 ounces undercharged of 134A can make such a huge difference. The temperature from the left vent to the right vent can vary 10 to 20 degrees. The easiest thing to try is to top off the system or better yet, remove all freon and recharge the unit with the factory specified amount. In most cases after the proper charge of Freon is in the car, the temp will blow equally as cold like it should on BOTH sides!

What if that didn’t help? Read on to learn of another possible cause of the problem.

HVAC Door Issue

Dual zones supplying different temperatures from vents on either side of the dash is achieved by the use of small doors within the HVAC housing. By controlling the doors, the temperature of the air on the left and right can be adjusted to the desired comfort level. Many times the motor (or actuator) that controls the door for either side can fail or the door itself can break and prevent the temp. from being adjusted. Diagnosing this problem is more complex and can be a subject for another article. Thanks for reading. Hopefully, the free information provided here will help to remedy the problem of “AC’s blowing hot or warm from one side of the dash.”

Source by Dennis Bandy

2022 Audi A8 First Look: A Sharpened Up Luxury Sedan

Recently, Audi revealed a slightly upgraded A8 luxury sedan. Basically, it is the next installment after the fourth-generation 8. Some changes include regular OLED taillights, airways grille, and new headlights.

It comes with a dynamic frontend design. The headlights use digital Matrix LED Technology. The lower edge of the headlights generates a contour over the upright air intakes. On the backside of the vehicle, you have OLED taillights.

S8 comes with three light signature styles, unlike the other variants that provide only two. In the S8, if you go for the dynamic mode, the backlights will turn into the dynamic exclusive signature. Besides, you also have the proximity indicator. And the functions include dynamic turn signals.

On the A8, Audi provides the S appearance unit. If you prefer a sportier look, you may not have much dynamism with SE dance. But you can customize and make a combo of the optional black and S experience packages. you may like the chrome package if you prefer embellishments that are quite prominent. As for as exterior paint options are concerned, you can choose from Ultra blue, manhattan gray, firmament blue, and metallic district green.

The interior comes with a configurable, high-grade material. Plus, there is a wide range of equipment and seed layouts. Besides, the cabin uses the MMI system of Audi and features a pair of touch screens. One screen is 8.6 inches and the other is 10.1 inches.

The virtual cockpit is all digital if you prefer a digital gauge cluster. So, the navigation system is the next level. If you are an Audiophile, you can enjoy your playlist on this powerful sound system. Besides, the real compartment is also quite fancy, especially if you go for the A8 L model. These hidden feature options are galore. The center console is stretched-out. Plus, the footrest can heat and massage your feet.

In this vehicle, rear passengers can enjoy your favorite content on a beautiful 10.1-inch screen that is fitted to the front seatbacks. Plus, they can get a body massage and enjoy a cold beverage at the same time. There can fold out to tables as well. Plus, there is an air quality package that comes with a fragrance system, which is optional.

For climate control, there is a 4-zone air conditioning system. Plus, the headrests and seats are power-adjustable. In case you don’t know, there is an extremely luxurious A8 version that will be available for purchase in China only.

The A8 L Horch targets the Mercedes-Maybach S-Class. Plus, A8 features an extended wheelbase along with a posh interior. In other words, the interior includes an expanded panoramic roof, deep pile methods, embossed logos, diamond-pattern quilting, and soft throw pillows.

For the US market, the powertrain choices will be the same. It includes both the twin-turbo V-8 that produces a torque of 590 lb-ft and the hybrid V-6. The 2022 Audi A8 will be out to purchase in December in the UK. The price of the base unit is $115,000 while the price of the S variant is $168,000.

Source by Shalini M

Staging an Open House

Houses for sale will receive more offers when an open house is staged correctly. The reason that this works so well is that clearing out the homeowners personal things potential buyers can see their things in the houses for sale easier. To stage a correct open house and receive more offers for the home, there are steps that you must take.

Step one

Look at your home with a buyer’s eye and see what turns you off about the home that can be fixed for a small amount of money and little time. One thing that is an easy fix it change unattractive paint colors. It is best if you choose neutral colors or some shade of white. This makes it easier for a potential buyer to picture the walls done in their favorite colors.

Step two

Once you have any paint issues taken care of look at any fixes that need to be dome to the outdated or dated areas of your home. For example, in the kitchen the cabinets can be updated by just changing the hardware. If they have been painted and the paint is peeling, you should scrape the paint off and either paint them again or varnish them. Although it could be expensive and time consuming if the floor is tile or linoleum and it is stained or cracking you should replace it. No potential buyer wants to walk into a room and see stained, cracked flooring. This goes for the bathroom also. In the bathroom, make sure that if there is tiling around the tub or the shower you need to make sure it is clean, mildew, and mold free. You also need to make sure that the carpet is clean and odor and stain free.

Step three

Many houses for sale have small repairs that will need to be repaired before hosting an open house. Take time to check out every room for any repairs such as loose floorboards, a missing railing on the staircases, cracks in the walls, electrical sockets that do not work, or burnt out lights.

Step four

Rent storage unit and move personal accessories and unneeded furniture to the unit. This can include small or large pieces of furniture that does not need to be in the home, personal collections, and family photos. You can make the rooms look more spacious if you keep the furnishings down to the basics. Make sure that every room serves a purpose like a family room, bedroom, etc. You can add accent pieces but not more than is necessary. These pieces can include plants, artwork, and pottery. Make sure that the lawn is mowed.

Following these tips for a successful open house will get more offers on houses for sale.

Source by Lora Davis

Mulliner Develops Massive 22-Inch Carbon Fiber Wheels for Bentley

If you cannot spend money on your Bentley Bentayga due to the lack of good quality Carbon fiber rims, you are on the right page. The good news is that Mulliner has a solution for you. The customization and coachbuilding division of the company is of great interest when it comes to developing high-quality products like this. If you go for these 22 inch Carbon fiber wheels, you can solve this problem once and for all. Let’s get a deeper insight into the massive 22-inch carbon fiber wheels for your Bentley. Read on to find out more.

Apart from being flashy and enormous, you can enjoy a lot of other practical benefits if you purchase carbon fiber wheels. Although there are many benefits, one of the most prominent ones is that the wheels are 13 pounds lighter than a similar forged aluminum wheel.

In other words, you can reduce 52 pounds of mass if you replace all of the four wheels. And the good thing about this reduction of the mass can help you improve your acceleration, handling, and quality. As a matter of fact, 13 pounds per rim is a lot of mass to lose. So, it can really make a difference in these aspects.

According to Bentley, the increased stiffness of the rims offers a lot of benefits. For example, in case of a sudden hit, your aluminum wheel can break down. On the other hand, the woven construction of the carbon fiber wheel reduces air loss in case of a serious head. Therefore, it reduces the likelihood of an accident, as your safety must be your number one priority.

Apart from this, it may also help reduce wheel deflection. Again, this can improve handling due to the consistent camber corner. As a matter of fact, even if you go for forged aluminum rims, they can flex in response to hard cornering. Although we cannot say for sure if you can have a problem because of cornering hard, the secondary benefits can help increase the sales of the wheels.

However, the woven texture is the best selling point. This structure is visible below the 10-spoke rims. Since Carbon fiber has been quite popular when it comes to beauty and structure, the appeal of the weave is still the same. These wheels feature a technical sporty look that adds to the beauty of Bentley.

If you want to purchase one, you should be ready to shell out a lot of money. In other words, you may have to spend a little more to make your vehicle more exclusive. As far as the release date is concerned, the new rims will be available to purchase later this year.

In short, this was a brief look at Mulliner 22-inch carbon fiber wheels. They are a new installment by the manufacturer. If you are in need of one, you can make this purchase to upgrade your Bentley. Just make sure you can afford this upgrade and that’s all you need to do.

Source by Shalini M

What Are the Common Symptoms of Blocked Drains?

A blocked drain are created by a blockage in a drain pipe connected to your home through your bathrooms, toilets, laundry & kitchen.

The most common cause of drain becoming clogged are from large objects being flushed. Drains are not designed to cope with large object including:

  • Sanitary Products
  • Baby Wipes
  • Toilet Deodorant block holders
  • Etc…

Other causes of blockages are Tree Roots. Tree roots find their way through into pipes through the crack or joints of pipes & through breaks in the pipe wall.

What are the signs or symptoms?

There are many different causes of blockages. The most common symptoms or signs include:

  • Water is filling up in the shower. Only after you get out of the shower you notice the water starting to retreat.
  • The toilet seems to continue to fill up and takes a while for the water levels to draw back to normal
  • Your getting some bad smells & odours wafting through the house, kitchen, bathrooms or laundry

There are also many causes of drainpipes becoming clogged up. Some of the most common symptoms of signs of a blocked drain pipe include

  • The water level is growing when you run the tap in the sink. You come back a few minutes later and notice the water levels on starting to drop
  • You flush the toilet however the waste does not disappear. You come back several minutes later to notice the water levels have only gone down by half
  • You look outside only to notice there is an overflow

Recommendations for a Plumber for people living in Melbourne, Victoria, Australia

There are many good plumbers in Melbourne that are more than capable of assisting you properly without breaking the bank.

I suggest you check the plumber out before you give them a call as proper insight into your problem & the solution needed can potentially save you thousands in future plumbing bills.

If you are experiencing blocked drains or blocked sewers & are looking for an affordable plumber in Melbourne, I would have to recommend you give O’Shea Plumbing a try.

Source by Leigh Walker

This Massive Bentley Mulsanne Limo Should Ensure You Command Maximum Attention

Whether you are a beginner or an experienced user, The Mulsanne Grand Limousine is an ideal choice for Plutocrats and Autocrats like you. This vehicle comes with an iron fist and absolute power with a bit of correction here and there. So, if you have a lot of spare money sitting in your bank account, you can make use of it by purchasing this beautiful vehicle. If you are looking for a fitting automobile, you are on the right page. According to many experts in this field, the Bentley Mulsanne Grand Limousine by Mulliner is one of the best vehicles to cover your needs.

Although the typical Mulsanne was an ideal option for the rulers, it has already been discontinued. The great thing about this beauty is that it takes things to a whole new level. The in-house bespoke arm adds around one meter of length to the vehicle. Therefore, the total length of the vehicle is about 21 feet. Apart from this, the roof of the vehicle is elevated by 3 inches, which increases the space in the cabin. Therefore, passengers can easily get in and out of the massive cabin.

Apart from this, the Imperial Blue Linen interior gives a luxury look two Bentley. In addition, there is a glass partition between the drivers and the passengers sitting behind. Therefore, the passengers don’t need to worry about their conversation being heard by the drive.

Besides, the rear has plenty of space for 4 people who can sit face to face. Therefore, the passengers can have fun together. Apart from the prestige of a slab of luxury, this beautiful vehicle allows the middle class to have a little exclusivity as well. Therefore, it is an All-in-One pack for today’s bourgeoisie. If you can’t afford to spend a lot of money on one, we suggest that you give a go to this one. And we be that you won’t regret this call.

In other words, it is a brand new vehicle that you can roll around in. As far as the oily bits of this vehicle is concerned, it is just like any other regular car. Let us take a look at the engine specifications of this great vehicle.

As far as the power of the engine is concerned, Bentley comes with a Twin Turbo V8 engine. This 6.8-liter engine produces 752 lb-ft of torque and 505 horsepower, which is more than enough to give you a thrilling experience.

This limo comes with 21-inch wheels. What makes it stand out from the crowd is the Silver Frost paintwork that covers the top half of the body. On the other hand, the bottom half is Moroccan Blue. And this combo is quite attractive.

Today, there are 5 of the limos out there for sale as the Bentley Emirates has just reacquired them. It’s interesting to note that all of the 5 were under the possession of the same owner. They have had them since 2015. Therefore, if you find this grand-limo interesting, you can give it a go today.

Source by Shalini M

The Responsible Builder’s Guide to Surface Protection for Hospital Renovation Projects

Although the construction industry was severely damaged by the Great Recession, there is one particular area where business is growing; hospital construction and renovation. Due to the increase demand for healthcare services by aging baby boomers, hospital construction and renovation projects have increased dramatically in the past ten years and will continue to grow in the future. According to McGraw-Hill Construction Research and Analytics, health care construction has increased six percent during 2011, outperforming the overall non-residential construction market. Although undertaking a hospital renovation project can be highly lucrative, there are many important rules and regulations that require full compliance by the contractor. Failure to meet these regulations could result in lawsuits or even worse, in the deaths of hospital patients. To avoid calamity, there are several extremely important things to know upon beginning renovation.

First and foremost, builders must meticulously contain dust disturbed by renovation activities. Allowing airborne particulates to circulate through the hospital could mean death for sensitive patients. On a hospital renovation jobsite at St. Joseph’s Hospital, Inc. in Tampa, FL, three children battling leukemia, ages two, five, and nine died after contracting fungal infections. The pathogenic fungi was released and circulated through the air conditioning systems from construction activities on the floor below. To avoid tragic scenarios such as this, builders must contain dust particulates as much as possible.

Secondly, while accessing electrical panels and ceiling wiring, subcontractors should use mobile containment units with negative air pressure to fully contain dust. Mobile containment units are small, portable enclosures that allow builders access to ceiling and wall panels without permitting particulates generated from sanding, drilling, etc. to circulate through the air. A few businesses allow contractors to rent mobile containment units but for large scale projects, investing in one or two will save time and money in the long run. For more details about mobile containment contact your local surface protection suppliers.

Another important aspect of dust control for primary contractors on the renovation project is preventing the spread of dust from subcontractors. Large-scale renovations typically require tens or hundreds of workers, and since meticulously preventing the spread of dust is so critical, these workers must all make a great effort to avoid contamination. Employee education is a great place to start, along with the requiring workers to wear personal protection. In order to help you comply with regulation there are several products that may make a huge difference; sticky mats, shoe covers, and coveralls. Require subcontractors to wear shoe covers and use fresh pairs as often as necessary. Install a sticky mat at each door entrance. Many adhesive mats are inexpensive and available in packs of four with thirty pages on each mat, so make sure to replace sticky sheets often.

A third important point is to be aware of fire-resistance requirements for your protection materials. When installing Zipwall™ systems for dust control or protecting a newly-installed concrete floor, use products that are certified as fire-resistant to avoid violating regulations. Large 4′ x 8′ sheets of fire-resistant corrugated plastic are also great for protecting wall panels, floors, doors, and more. Coverguard™ is another great option for a fire-resistant floor protection product that meets hospital renovation requirements.

These are only a few recommendations for preventing dust and protecting valuable fixtures during hospital renovation projects. For more information, contact Pat Mullen at Builders Site Protection and check out the OSHA website for easy-to-follow guidelines to understanding and fully complying with regulations.

Source by Heather Ley

BMW I Vision Circular Concept First Look: Renew, Reuse, Recycle

Manufacturers of vehicles are getting ready for future electric vehicles. Converting the vehicle fleet from internal combustion engines to fully electric units will consume a lot of resources. In this department, BMW seems to be ahead of the competition. Recently, it has come up with I Vision Circular concept car.

Apart from a couple of laser-etched logos, you won’t find any exterior badges. This approach can help save a lot of energy and tooling required to produce this type of decor. After all, there is no need to go for chrome-looking coaching if an etching can serve the purpose.

It looks like that the manufacturer has attempted to save on weight in an attempt to reduce carbon emissions. In fact, this concept is unique and more important than the futuristic hatchback concept. As a matter of fact, it represents a process that had a system of production. And without any doubt, this concept is very cool.

Primarily, this concept is cool because of the outrageous features of the I Vision Circular. And there is a carbon footprint analysis. Apart from this, BMW is trying to go green and save the environment by reducing carbon emissions by up to 40%. And we know that this will have a lot of positive impact on the environment.

Apart from the conceptual stuff, we can say that this vehicle is going to be interesting for users. This stocky, squat thing features cab-forward proportions and pronounced angularity. The sloping windshield goes straight down to the massive kidney grille, which is a futuristic design by BMW. However, it’s much better integrated compared to the existing models.

As far as paint is concerned, there is nothing. The aluminum body is anodized and the rear part is treated with heat until it turns blue. So, recycling the bodywork will be a lot easier down the road. So, it serves a lot of purposes.

Also, the windshield is known as the instrument cluster while the back glass serves as the turn signals and taillamps. Similarly, the window features strips of screens that are touch-sensitive for easy entry.

For recycling, components of this vehicle are pared down. So, they are easy to remove. Every door features a built-in electronic module. It serves as a window motor, a switch, and a module that can be removed.

Plus, a special tool should be used to remove the sparse fasteners. So, the process of assembly and disassembly is quite easy. In other words, if you don’t attach something with a fastener, you can remove it without a problem just like the recycled upholstery attached to the frames of the seat with a cord system.

Without any doubt, BMW I Vision Circular is a concept car that you can depend on. This futuristic car can help you enjoy a new design and a lot of luxurious features. Let’s wait for this car to come out.

Source by Shalini M

Masonry Chimney Repair – Getting it Right For Your Home

There are chimneys in most homes, adding to the warmth within the home. The difference between various homes’ chimneys is the actual construction and design of the chimney. A masonry chimney is one type of flue that is quite common in many homes, and many times with age will require some sort of repair.

Use of any flue will eventually age it and age through elements will definitely erode any structure, making it necessary to maintain your masonry chimney in the most proper way. It’s inevitable that everyone isn’t a masonry flue repairer, which means that you must not only know when your flue needs fixing, but just who to employ for the job.

It is most often needed to perform some sort of masonry chimney repair when your home’s vent has been in place for many years. This is most common when purchasing a home that hasn’t been occupied in a while. Even if you have occupied your home but haven’t used your vent in a while, the nonuse could allow it to wear with age. If you don’t frequently clean or provide maintenance to your flue, it can often erode or become damaged through time. Any of these situations could greatly require the need for a great flue repair company to provide the most appropriate repairs for your chimney repair needs.

Getting just any chimney fixing company will not do. You must do your due diligence and research companies to find those that are most experienced and skilled in the repair as this is a major fixture within your home. If the job is not performed correctly, you will end up having more costs down the road and most likely worse damages than before.

With a masonry flue created of solid units made from brick, stone, or other masonry material, the company you choose should be able to provide the materials needed to perform the most accurate and proper repair to your specific vent. Masonry chimneys are also lined with specialized fire clay flue liners, meaning that the company you choose should also be able to provide the most appropriate lining for replacement to your original chimney.

When you are able to distinguish the need for masonry chimney repair, you will be better able to choose the right company based on what you need. You should be able to find a company that can provide you with a great repair service, that is accompanied by a great price.

Source by Derek Farley

How Popular Is Prefabricated Housing?

Unlike in the world of human interactions, popularity is equated with quality in the world of technology. The AEC industry is firmly supported by the technological advances of our age, and prefabricated housing is becoming increasingly popular. The emergence of prefabricated or modular construction in the housing industry is an affordable and reliable solution to the challenge of quality housing worldwide. Prefabricated housing, sometimes known as prefab homes, prefabs or modular homes, are manufactured off site in sections, from just bathrooms to entire floors, that can be transported, placed or assembled to form housing units. Prefabricated housing can be independent dwelling units for individual families (houses) or single units which have been stacked on top of each other to form multi-storey housing or apartment blocks. How useful prefabrication is in the housing sector, why it is so and who can deliver services key to accurate prefabrication design are some of the things we will explore.

So, what are prefabricated buildings?

Prefab buildings can be built from components (such as panels), modules (in the case of entire modular homes, houses on wheels) or sections (parts of manufactured homes) constructed off site and transferred to the site when they are ready to be installed. A team of technical experts attach the different services to the building layout. These can include double-storey homes and customised homes. Modular or prefabricated homes can be created in sections and then transported on site to be put together as part of the construction process or installed. Whole rooms, such as bathroom pods or kitchens, can be created in a factory setting as prefabricated units. Steel frames can be erected on site to ‘slot’ in the prefabricated units or entire concrete foundations can be laid into the ground in readiness for the new home to arrive. Financing, construction and appraisals of these homes are carried out in the same way as for regular homes. Prefabricated houses can also be assembled on production assembly lines, which are transferred in complete sections or floors to the site, where these complete home units are connected floor by floor and then also connected to the location’s main water supply, sewage system and electrical lines.

How are they constructed?

They are usually constructed in factories that are some distance away from the actual housing site, indeed they could be in a different country. These purpose-designed factories effectively consist of assembly line environments, where different elements and trades come together at different stages of the assembly line to add the various components to the building. Starting with floors, walls and ceilings, the structure moves along for internal fixtures and MEP elements such as piping, plumbing, boilers, bathrooms and entire kitchen fittings, before being moved across to finishing areas such as glazing, doors, electrical fittings and even bathroom tiling. Once the house is assembled, it passes through final QA checks before being handed over to logistics teams for transport to its permanent site.

Plumbing and electrical lines are connected to the city’s water and electrical connections and the prefabricated sections are sealed. Prefabricated homes can have a number of rooms and be of different designs. These homes can be set on a permanent foundation, blending in seamlessly with other regularly constructed homes. Repairs on the homes are conducted by the real estate company involved in its sale.

During the settling-in time period, a prefabricated home ‘settles’ in to the location, after which some cracking of the drywall could occur. Appliances that were incorrectly installed can be repaired by changing the wiring or plumbing, and the ventilation, heating, cooling, plumbing and electrical systems can be properly installed by a set-up crew.

One of the driving forces behind a successfully assembled and reliably functioning prefabricated home is the effectiveness of its design. Increasingly, architects, engineers, contractors and trade contractors use BIM (Building Information Modelling) construction drawings at some point as part of DfMA (Design for Manufacture and Assembly). DfMA is a design process that groups the design for manufacture, or the ease with which parts will be made for a product, with the design for assembly, which refers to the ease with which parts will be assembled. DfMA helps the design team reduce manufacturing and assembly costs by identifying, analysing and removing waste and inefficiency from a product’s design. DfMA modelling and drawing is fast becoming synonymous with design for prefabrication.

Construction drawings, or shop drawings, graphically illustrate the details, data and specifications of a prefabricated design, contain information about the MEP (M&E) systems and include the details of prefabricated components. BIM technology is part of the larger virtual design and construction (VDC) process that helps find solutions to challenges faced by subcontractors and designers before building prefabricated components in the factory.

Advances in technology have made it possible and indeed preferable to outsource the delivery of BIM services such as modelling and drafting. Outsourced firms specialise in delivering drawings and models quickly, using the latest software, such as Autodesk 3ds Max, Autodesk Revit, Autodesk Navisworks and others, and by employing well-qualified experts. Modular construction drawings provided by these CAD drafting firms are typically accurate and error-free.

Prefabricated construction has reportedly been used in the world’s tallest building, the Burj Khalifa, in Dubai and in the construction of the prestigious Sydney Opera House.

Advantages of Prefabrication

  • Faster completion of projects, therefore reducing costs
  • Diverse uses – can be used to create high-rises, single-storey construction, villas, townships, as well as to create ceiling slabs, terrace blocks, wall panels, columns, staircases, bathrooms, light fixtures, etc.
  • Customisation – unique property specifications can be accommodated easily, resulting in reduced expenses
  • Durability – prefabrication in the structural aspect of construction bolsters structural strength, sometimes helping to withstand earthquakes and other natural disasters. Concrete panels are created with elements of high quality in a controlled factory environment and therefore last longer.
  • Well suited for certain sectors that have repetitive design elements, such as student housing, educational institutions, healthcare facilities, prisons, police stations and senior housing.
  • Increased and more efficient quality control in factory settings
  • Safer and less stressful working environment for labourers in a factory than on site, especially in crowded areas, as on-site dangers are eliminated for workers
  • Less on-site space is required to assembly components which have already been assembled off site
  • Less waste is generated during construction, since prefabricated component waste is disposed of at the factory and not transported to the site
  • Competitive edge – allows flexibility in design decisions till the nth moment
  • Saves space – housing can be built in cramped spaces in tight schedules and take up less space

Modular construction in the housing industry has expanded its scope for buyers and builders. Buyers have more options to choose from and builders have more build options for construction, changing the overall construction landscape. Projects see MEP contractors use an increasing number of modular construction plans during collaboration. Prefabricated construction is more affordable and more green, since such buildings are better sealed against drafts and there is improved quality control systems in factories, thus leading to improved insulation and better energy efficiency. This will ultimately benefit neighbourhoods and residential and commercial projects.

The various advantages of using prefabricated housing can only be enjoyed when the DfMA modelling and drawings are flawless. Since this demands considerable time and resources, an increasing number of Western firms are looking overseas for their prefabrication design services.

Benefits of Outsourcing Prefab Design Services

  • Cost reduction, since skilled labour and expenditure on resources overseas is significantly less expensive
  • Use of advanced tools and technologies, such as AutoCAD and Revit, by experienced and well-qualified human resources
  • Standardisation of drawings across projects, so that MEP installations and other services are made easier
  • 3D axonometric drawings of the entire construction project are generated, showing methods and means by which individual subcontractor components or systems can be placed in the project
  • Skilled draftsmen and other technical professionals work faster, maintain accuracy, provide complete audit trails with drawing references, approval records
  • Faster turnaround time, since overseas firms employ ready and dedicated teams of trained personnel capable of working to constantly changing specifications, helping to complete projects on schedule
  • Increased flexibility, as outsourcing allows Western firms to pick and choose services according to need. The flexibility thus generated helps expand the business.

Outsourcing prefabrication design services is thus an increasingly popular option, and this approach will save time, increase productivity, ensure higher safety levels and increase profits. Using Revit, AutoCAD and other software to create modular construction drawings and models helps provide high-quality prefabricated design support for Western firms in the industry.

Source by Kuldeep Bwail